; 7330 ION Rev B Setup Assistant
[SetupInfo]
SetupScreens=1
Screen1=Setup Assistant

[Setup Assistant]
AssistantText=Welcome to the Setup Assistant! The following dialogs guide you through device setup. Select from the left which setup you wish to perform or press the Next button to cycle through all of the different setups.
AssistantCount=11
Assistant1=Template
Assistant2=Basic Setup
Assistant3=Comm Settings
Assistant4=3rd Party Protocols
Assistant5=Clock
Assistant6=Demand
Assistant7=Energy Pulsing
Assistant8=Analog Outputs
Assistant9=Memory
Assistant10=EnergyDemand Log
Assistant11=Reports
PrintList=0,7,15,0,1,1,15,15,1,3

[Template]
TabCount=4
Tab1=Save to PC
Tab1Type=2
Tab1Text=You can save the meter's entire configuration and store it to a .DCF file. You need this file when you upgrade the meter firmware, or you can send the .DCF file onto other ION meters of the same type.
Tab1Buttons=1
Tab1Button1Label=Save
Tab1Button1=1,1
Tab1Registers=4
Tab1Reg1=3,1,0x1300
Tab1Reg2=3,1,0x1303
Tab1Reg3=3,1,0x1304
Tab1Reg4=3,1,0x137D
Tab2=Send to Meter
Tab2Type=2
Tab2Text=Sends a previously stored meter configuration file (.DCF) into an ION meter.
Tab2Buttons=1
Tab2Button1Label=Send
Tab2Button1=1,2
Tab2Registers=4
Tab2Reg1=3,1,0x1300
Tab2Reg2=3,1,0x1303
Tab2Reg3=3,1,0x1304
Tab2Reg4=3,1,0x137D
Tab3=Firmware Upgrade
Tab3Type=2
Tab3Text=To get new features for your meter, you can upgrade a meter's firmware to a newer version. NOTE: You must specify a .DCF, or device configuration file. If you do not have one, use the Save to PC tab to create a file of your meter's present configuration.
Tab3Buttons=1
Tab3Button1Label=Upgrade
Tab3Button1=1,3
Tab3Registers=4
Tab3Reg1=3,1,0x1300
Tab3Reg2=3,1,0x1303
Tab3Reg3=3,1,0x1304
Tab3Reg4=3,1,0x137D
Tab4Firmware=270
Tab4=Register Edit
Tab4Type=2
Tab4Text=Allows you to view and modify energy register values
Tab4Buttons=1
Tab4Button1Label=Display
Tab4Button1=0,8
Tab4Registers=1
Tab4Reg1=11,1,Energy
Tab4Reg1Groups=3
Tab4Reg1Group1Label=kWh
Tab4Reg1Group2Label=kVARh
Tab4Reg1Group3Label=kVAh
Tab4Reg1Group1Displays=4
Tab4Reg1Group1Display1=0x58B0
Tab4Reg1Group1Display1Label=Imported
Tab4Reg1Group1Display2=0x58B1
Tab4Reg1Group1Display2Label=Exported
Tab4Reg1Group1Display3=0x58B2
Tab4Reg1Group1Display3Label=Total
Tab4Reg1Group1Display4=0x58B3
Tab4Reg1Group1Display4Label=Net
Tab4Reg1Group2Displays=4
Tab4Reg1Group2Display1=0x58B4
Tab4Reg1Group2Display1Label=Imported
Tab4Reg1Group2Display2=0x58B5
Tab4Reg1Group2Display2Label=Exported
Tab4Reg1Group2Display3=0x58B6
Tab4Reg1Group2Display3Label=Total
Tab4Reg1Group2Display4=0x58B7
Tab4Reg1Group2Display4Label=Net
Tab4Reg1Group3Displays=4
Tab4Reg1Group3Display1=0x58B8
Tab4Reg1Group3Display1Label=Imported
Tab4Reg1Group3Display2=0x58B9
Tab4Reg1Group3Display2Label=Exported
Tab4Reg1Group3Display3=0x5FA1
Tab4Reg1Group3Display3Label=Total
Tab4Reg1Group3Display4=0x5FA2
Tab4Reg1Group3Display4Label=Net

[Basic Setup]
TabCount=3
Tab1=PT/CT Ratios
Tab1Type=2
Tab1Text=Allows you to program PT and CT ratios.
Tab1Buttons=1
Tab1Button1Label=Edit
Tab1Button1=0,4
Tab1Registers=5
Tab1Reg1=1,1,0x7800
Tab1Reg1Text=This is the meter operating mode.
Tab1Reg2=0,1,0x7000
Tab1Reg2Text=This is the primary rating for the meter potential transformers.
Tab1Reg3=0,1,0x7001
Tab1Reg3Text=This is the secondary rating for the meter potential transformers.
Tab1Reg4=0,1,0x7002
Tab1Reg4Text=This is the primary rating for the meter current transformers.
Tab1Reg5=0,1,0x7003
Tab1Reg5Text=This is the secondary rating for the meter current transformers.
Tab2=Nameplate Info
Tab2Type=2
Tab2Text=Allows you to program meter nameplate information.
Tab2Buttons=1
Tab2Button1Label=Edit
Tab2Button1=0,4
Tab2Registers=8
Tab2Reg1=3,0,0x1300
Tab2Reg2=3,0,0x1303
Tab2Reg3=3,0,0x1304
Tab2Reg4=3,1,0x137D
Tab2Reg4Text=This is where you can program the meter template string.  NOTE: Modifying this value manually may cause some functions to not operate properly and should only be done by advanced users.
Tab2Reg5=3,0,0x1302
Tab2Reg6=3,1,0x1345
Tab2Reg6Text=This is where you can program the meter owner (utility) information.
Tab2Reg7=3,1,0x1346
Tab2Reg7Text=This is where you can program the meter location (customer) information.
Tab2Reg8=3,1,0x1347
Tab2Reg8Text=This is where you can program the meter identification information. NOTE: If this field is not blank, MV-90 requires their Device ID field to match this field.
Tab3=Rollover
Tab3Type=2
Tab3Text=Allows you to program energy rollover information.
Tab3Buttons=1
Tab3Button1Label=Edit
Tab3Button1=0,4
Tab3Registers=1
Tab3Reg1=0,1,0x721E
Tab3Reg1Warning=1
Tab3Reg1Text=This specifies the reading at which energy values will reset back to zero.  NOTE: Values of 10 million or lower are recommended for resolution purposes.
Tab3Reg1Multi=1
Tab3Reg1Label=Energy Rollover

[Comm Settings]
TabCount=4
Tab1=Com1
Tab1Type=2
Tab1Text=Allows you to modify the Com1 communication settings.
Tab1Buttons=1
Tab1Button1Label=Edit
Tab1Button1=0,4
Tab1Registers=4
Tab1Reg1=1,1,0x7A4F
Tab1Reg1Text=This specifies which communication protocol is active (Must be Modemgate if modem is installed).
Tab1Reg2=0,1,0x71E9
Tab1Reg2Text=This specifies the unit ID used to identify the meter during communications.
Tab1Reg3=1,1,0x7987
Tab1Reg3Text=This specifies the comm port baud rate used during serial communications.
Tab1Reg4=3,1,0x5050
Tab1Reg4Text=This specifies the modem initialization string used if a modem is present.
Tab2=Com2
Tab2Type=2
Tab2Text=Allows you to modify the Com2 communication settings.
Tab2Buttons=1
Tab2Button1Label=Edit
Tab2Button1=0,4
Tab2Registers=3
Tab2Reg1=1,1,0x7A50
Tab2Reg1Text=This specifies which communication protocol is active (Must be Ethergate if Ethernet is installed).
Tab2Reg2=0,1,0x7234
Tab2Reg2Text=This specifies the unit ID used to identify the meter during communications.
Tab2Reg3=1,1,0x7A4D
Tab2Reg3Text=This specifies the baud rate used during serial communications.
Tab3=Optical
Tab3Type=2
Tab3Text=Allows you to modify the ANSI optical port communication settings.
Tab3Buttons=1
Tab3Button1Label=Edit
Tab3Button1=0,4
Tab3Registers=3
Tab3Reg1=1,1,0x7A51
Tab3Reg1Text=This specifies which communication protocol is active.
Tab3Reg2=0,1,0x7235
Tab3Reg2Text=This specifies the unit ID used to identify the meter during communications.
Tab3Reg3=1,1,0x7A4E
Tab3Reg3Text=This specifies the baud rate used during serial communications.
Tab4=Ethernet
Tab4Type=2
Tab4Text=Allows you to modify the Ethernet communication settings.
Tab4Buttons=1
Tab4Button1Label=Edit
Tab4Button1=0,4
Tab4Registers=6
Tab4Reg1=3,1,0x1348
Tab4Reg1Text=This specifies the TCP/IP Ethernet address.
Tab4Reg2=3,1,0x1349
Tab4Reg2Text=This specifies the Ethernet subnet mask.  Subnet masks of 0.0.0.0 and 255.255.255.255 are not permitted.
Tab4Reg3=3,1,0x134A
Tab4Reg3Text=This specifies the gateway address if one is being used.
Tab4Reg4=3,1,0x137F
Tab4Reg4Text=This specifies the IP address (or the fully qualified domain name if DNS is active) of the SMTP Server.
Tab4Reg5=4,1,0x477F
Tab4Reg5Text=This specifies the connection timeout for the SMTP Server.
Tab4Reg6=1,3,0x7EBD
Tab4Reg6Text=Specifies whether to allow configuration through WebServer interface.

[3rd Party Protocols]
DefaultDisplayGroups=6
DefaultDisplayGroup1=1
DefaultDisplayGroup2=2
DefaultDisplayGroup3=3
DefaultDisplayGroup4=4
DefaultDisplayGroup5=5
DefaultDisplayGroup6=6
TabCount=2
Tab1=Modbus Slave
Tab1Type=8
Tab1Manager=0x8F
Tab1Text=Allows you to customize the Modbus map used by other 3rd party device to communicate to the meter.
Tab1Buttons=1
Tab1Button1Label=Edit
Tab1Button1=0,4
Tab1Button2Label=Send
Tab1Button2=0,13
Tab2=DNP 3.0
Tab2Type=9
Tab2Manager=0xA1
Tab2Manager2=0xA0
Tab2Text=Allows you to customize the DNP 3.0 map used by other 3rd party device to communicate to the meter.
Tab2Buttons=1
Tab2Button1Label=Edit
Tab2Button1=0,4

[Clock]
TabCount=2
Tab1=Timezone
Tab1Type=2
Tab1Text=Allows you to program the meter clock settings.
Tab1Buttons=2
Tab1Button1Label=Edit
Tab1Button1=0,4
Tab1Button2Label=TimeSync
Tab1Button2=0,7
Tab1Registers=6
Tab1Reg1Label=Timezone
Tab1Reg1=5,3,0x722E
Tab1Reg1Text=Specifies the difference in hours between the meter's timezone and GMT.
Tab1Reg2=1,3,0x7BB8
Tab1Reg2Text=Specifies the type of time synchronization used to update the meter clock.  NOTE: Most software transmits time using the UTC format while some DNP masters and GPS may use localtime format.
Tab1Reg3=1,3,0x7BB7
Tab1Reg3Text=Specifies the ONLY communication port that time updates would be accepted on.  NOTE: Time synchronization signals on other ports will be ignored.
Tab1Reg4=1,3,0x7C24
Tab1Reg4Text=Specifies how the meter should maintain clock accuracy between time updates.  NOTE: If using GPS synchronization, this register should be set to COMMS.
Tab1Reg5=4,3,0x7231
Tab1Reg5Text=Specifies the amount of time the meter clock is moved forward when entering Daylight Savings.  NOTE: A value of zero will disable this feature and the clock will not adjust for DST.
Tab1Reg6=2,2,0x5B7D,1
Tab1Reg6Text=This displays the present meter localtime based upon the timezone setting set above and any time synchronization signal received on the Time Sync Source.
Tab2=DST Settings
Tab2Type=2
Tab2Text=Allows you to program the meter Daylight Savings periods.
Tab2Buttons=1
Tab2Button1Label=Edit
Tab2Button1=0,4
Tab2Registers=2
Tab2Reg1=2,3,0x722F
Tab2Reg2=2,3,0x7230

[Demand]
TabCount=1
Tab1=Rolling Block 
Tab1Type=2
Tab1Text=Allows you to program the interval used to compute your rolling demand values.
Tab1Buttons=1
Tab1Button1Label=Edit
Tab1Button1=0,4
Tab1Registers=2
Tab1Reg1=0,1,0x70C4
Tab1Reg1Warning=1
Tab1Reg1Multi=2
Tab1Reg1Label=Number of Sub-intervals
Tab1Reg1Text=This specifies the number of sub-intervals in use.
Tab1Reg2=4,1,0x70B4
Tab1Reg2Warning=1
Tab1Reg2Multi=3
Tab1Reg2Label=Sub-interval Length
Tab1Reg2Text=This specifies the duration of each of the sub-intervals.

[Energy Pulsing]
TabCount=4
Tab1=kWh Import
Tab1Type=2
Tab1Text=Allows you to program kWh imported pulsing via digital outputs.
Tab1Buttons=1
Tab1Button1Label=Edit
Tab1Button1=0,4
Tab1Registers=5
Tab1Reg1=0,1,0x777D
Tab1Reg1Text=Specifies the number of imported watt-hours that are accumulated per physical pulse.
Tab1Reg2=0,1,0x7773
Tab1Reg2Text=Specifies the minimum time interval in seconds between pulse transitions. NOTE: There is a minimum 50% duty cycle on all pulses.
Tab1Reg3=1,1,0x7E7B
Tab1Reg3Text=Specifies if the output pulse is a complete pulse or a KYZ transition.
Tab1Reg4=1,1,0x7A0B
Tab1Reg4Text=Specifies which physical digital output port the pulse occurs on.
Tab1Reg5=6,0,0x6274,1
Tab1Reg5Text=Indicates if the kWh imported is overloaded and pulsing to quickly.
Tab2=kWh Export
Tab2Type=2
Tab2Text=Allows you to program kWh exported pulsing via digital outputs.
Tab2Buttons=1
Tab2Button1Label=Edit
Tab2Button1=0,4
Tab2Registers=5
Tab2Reg1=0,1,0x777E
Tab2Reg1Text=Specifies the number of exported watt-hours that are accumulated per physical pulse.
Tab2Reg2=0,1,0x7774
Tab2Reg2Text=Specifies the minimum time interval in seconds between pulse transitions. NOTE: There is a minimum 50% duty cycle on all pulses.
Tab2Reg3=1,1,0x7E7C
Tab2Reg3Text=Specifies if the output pulse is a complete pulse or a KYZ transition.
Tab2Reg4=1,1,0x7A0C
Tab2Reg4Text=Specifies which physical digital output port the pulse occurs on.
Tab2Reg5=6,0,0x6275,1
Tab2Reg5Text=Indicates if the kWh exported is overloaded and pulsing to quickly.
Tab3=kVARh Import
Tab3Type=2
Tab3Text=Allows you to program kVARh imported pulsing via digital outputs.
Tab3Buttons=1
Tab3Button1Label=Edit
Tab3Button1=0,4
Tab3Registers=5
Tab3Reg1=0,1,0x777F
Tab3Reg1Text=Specifies the number of imported var-hours that are accumulated per physical pulse.
Tab3Reg2=0,1,0x7775
Tab3Reg2Text=Specifies the minimum time interval in seconds between pulse transitions. NOTE: There is a minimum 50% duty cycle on all pulses.
Tab3Reg3=1,1,0x7E7D
Tab3Reg3Text=Specifies if the output pulse is a complete pulse or a KYZ transition.
Tab3Reg4=1,1,0x7A0D
Tab3Reg4Text=Specifies which physical digital output port the pulse occurs on.
Tab3Reg5=6,0,0x6276,1
Tab3Reg5Text=Indicates if the kVARh imported is overloaded and pulsing to quickly.
Tab4=kVARh Export
Tab4Type=2
Tab4Text=Allows you to program kVARh exported pulsing via digital outputs.
Tab4Buttons=1
Tab4Button1Label=Edit
Tab4Button1=0,4
Tab4Registers=5
Tab4Reg1=0,1,0x7780
Tab4Reg1Text=Specifies the number of exported var-hours that are accumulated per physical pulse.
Tab4Reg2=0,1,0x7776
Tab4Reg2Text=Specifies the minimum time interval in seconds between pulse transitions. NOTE: There is a minimum 50% duty cycle on all pulses.
Tab4Reg3=1,1,0x7E7E
Tab4Reg3Text=Specifies if the output pulse is a complete pulse or a KYZ transition.
Tab4Reg4=1,1,0x7A0E
Tab4Reg4Text=Specifies which physical digital output port the pulse occurs on.
Tab4Reg5=6,0,0x6277,1
Tab4Reg5Text=Indicates if the kVARh exported is overloaded and pulsing to quickly.

[Analog Outputs]
DefaultDisplayGroups=4
DefaultDisplayGroup1=6
DefaultDisplayGroup2=4
DefaultDisplayGroup3=5
DefaultDisplayGroup4=2
TabCount=4
Tab1=Output 1
Tab1Type=4
Tab1Text=Allows you to program analog output configuration information.
Tab1Buttons=2
Tab1Button1Label=Edit
Tab1Button1=0,4
Tab1Button2Label=Unlink
Tab1Button2=0,10
Tab1Module=0x0200
Tab1Registers=3
Tab1Reg1=0,1,0x702A
Tab1Reg1Text=Specifies the minimum source value that matches the minimum possible analog output signal.
Tab1Reg2=0,1,0x7048
Tab1Reg2Text=Specifies the maximum source value that matches the maximum possible analog output signal.
Tab1Reg3=1,1,0x799F
Tab1Reg3Text=Specifies which physical analog output port the signal occurs on.
Tab2=Output 2
Tab2Type=4
Tab2Text=Allows you to program analog output configuration information.
Tab2Buttons=2
Tab2Button1Label=Edit
Tab2Button1=0,4
Tab2Button2Label=Unlink
Tab2Button2=0,10
Tab2Module=0x0201
Tab2Registers=3
Tab2Reg1=0,1,0x702B
Tab2Reg1Text=Specifies the minimum source value that matches the minimum possible analog output signal.
Tab2Reg2=0,1,0x7049
Tab2Reg2Text=Specifies the maximum source value that matches the maximum possible analog output signal.
Tab2Reg3=1,1,0x79A0
Tab2Reg3Text=Specifies which physical analog output port the signal occurs on.
Tab3=Output 3
Tab3Type=4
Tab3Text=Allows you to program analog output configuration information.
Tab3Buttons=2
Tab3Button1Label=Edit
Tab3Button1=0,4
Tab3Button2Label=Unlink
Tab3Button2=0,10
Tab3Module=0x0202
Tab3Registers=3
Tab3Reg1=0,1,0x702C
Tab3Reg1Text=Specifies the minimum source value that matches the minimum possible analog output signal.
Tab3Reg2=0,1,0x704A
Tab3Reg2Text=Specifies the maximum source value that matches the maximum possible analog output signal.
Tab3Reg3=1,1,0x79A1
Tab3Reg3Text=Specifies which physical analog output port the signal occurs on.
Tab4=Output 4
Tab4Type=4
Tab4Text=Allows you to program analog output configuration information.
Tab4Buttons=2
Tab4Button1Label=Edit
Tab4Button1=0,4
Tab4Button2Label=Unlink
Tab4Button2=0,10
Tab4Module=0x0203
Tab4Registers=3
Tab4Reg1=0,1,0x702D
Tab4Reg1Text=Specifies the minimum source value that matches the minimum possible analog output signal.
Tab4Reg2=0,1,0x704B
Tab4Reg2Text=Specifies the maximum source value that matches the maximum possible analog output signal.
Tab4Reg3=1,1,0x79A2
Tab4Reg3Text=Specifies which physical analog output port the signal occurs on.

[Memory]
TabCount=1
Tab1=Status
Tab1Type=6
Tab1Warning=1
Tab1Text=Allows you to allocate the meter log memory.
Tab1Buttons=1
Tab1Button1Label=Edit
Tab1Button1=0,12
Tab1Logs=3
Tab1Log1=0x0800,0x719C,0x71BC,1
Tab1Log1Text=Allows you to control the duration of the specified log.
Tab1Log2=0x0B80,0x71E6,0x0000,1
Tab1Log2Label=Event Log
Tab1Log2Text=Allows you to control the number of events stored in the event log.
Tab1Log3=0x0801,0x719D,0x71BD,1
Tab1Log3Text=Allows you to control the duration of the specified log.
Tab1Modules=2
Tab1Module1=0x94,4
Tab1Module2=0x9C,14
Tab1SystemText=Indicates the amount of memory used by system resources in the meter.

[EnergyDemand Log]
TabCount=2
Tab1=Channels
Tab1Text=Allows you to program the Energy/Demand log inputs.
Tab1Type=4
Tab1Buttons=2
Tab1Button1Label=Edit
Tab1Button1=0,4
Tab1Button2Label=Unlink
Tab1Button2=0,10
Tab1Module=0x0800
Tab1Warning=1
Tab1DisplayGroups=3
Tab1DisplayGroup1=7
Tab1DisplayGroup2=1
Tab1DisplayGroup3=2
Tab2=Interval/Depth
Tab2Text=Allows you to specify the interval and duration of the log.
Tab2Type=2
Tab2Buttons=1
Tab2Button1=0,4
Tab2Button1Label=Edit
Tab2Registers=2
Tab2Reg1=4,1,0x71BC
Tab2Reg1Warning=1,0x0800
Tab2Reg1Label=Interval length
Tab2Reg1Text=This specifies the time interval between log recordings.
Tab2Reg2=0,1,0x719C
Tab2Reg2Warning=1
Tab2Reg2Text=This specifies the number of recordings the log can hold.

[Reports]
TabCount=1
Tab1=Meter Info
Tab1Type=2
Tab1Text=Allows you to view/store meter information.
Tab1Buttons=1
Tab1Button1Label=Display
Tab1Button1=0,8
Tab1Registers=4
Tab1Reg1=10,1,0x0F80,EnergyDemand Log
Tab1Reg1Text=This shows the meter energy/demand information.
Tab1Reg2=10,1,0x1000,Event Log
Tab1Reg2Text=This shows the meter event information.
Tab1Reg3=10,1,0x3,Meter Configuration
Tab1Reg3Text=This reports the meter configuration information.
Tab1Reg4=10,1,0x2,Template Comparison
Tab1Reg4Text=This reports the differences between a stored template and the meter template.